Micrel, Inc.
MIC2593
 
September 2008 
25
M9999-092208
 
12V Input Clamp Diode
The 12V input to the MIC2593 is the most negative
potential on the part and is therefore connected to the
chips   substrate   (as   described   in   Power   Supply
Decoupling, above). Although no particular sequencing of
the 12V supply relative to the other MIC2593 supplies is
required for normal operation, this substrate connection
does mean that the 12V input must never exceed the
voltage on the GROUND pin of the IC by more than 0.3
volts. Small amounts of internal leakage current can
cause this to happen when the VSTBY pins are energized
and the 12MVIN pins are not energized. In addition,
power supply output ringing or L(di/dt) effects in the wiring
and on the PCB itself will cause brief transient voltages in
excess of +0.3V to appear at the 12V input. For this
reason, it is required to clamp the 12V input to ground
with a Schottky diode. A diode rated at 1 amp and 20V to
40V as shown in our application schematic diagram is
suggested. The diodes anode should be physically
placed directly at the 12V input to the MIC2593, and its
cathode should have as short a path as possible back to
the parts ground. A good SMT part for this application is a
type MBRS140T3 (1A, 40V).
Gate Resistor Guidelines
The MIC2593 controls four external power MOSFETs,
that handle the high currents for each of the two 3.3V and
5V outputs. A capacitor is connected in the application
circuit from each GATE pin of the MIC2593 to ground.
However, an external capacitor, C
GATE
, is not required for
operation of the MIC2593. Each C
GATE
 controls the ramp-
up rate of its respective power output (e.g., 5VOUTB).
These capacitors, which are typically in the 10nF range,
cause the GATE outputs of the MIC2593 to have very low
AC impedances to ground at any significant frequency. It
is therefore necessary to place a modest value of gate
damping resistance (R
GATE
) between each C
GATE
 and the
gate of its associated MOSFET as shown in Figure 15.
These   resistances   prevent   high-frequency   MOSFET
source-follower oscillations from occurring. The exact
value of the resistors used is not critical; 10& to 33& is
usually a sufficient choice. Each R
GATE
  should be
physically located directly adjacent to the MOSFET gate
lead to which it connects.
MIC2593
GATE
R
GATE
C
GATE
10nF
External
MOSFET
 
Figure 15. C
GATE
 and R
GATE
 Connection
相关PDF资料
MIC2594-2BM TR IC CTRLR HOT SWAP NEG HV 8-SOIC
MIC2595R-2BM TR IC CTRLR HOT SWAP NEG HV 14-SOIC
MIC280-7BM6 TR IC SUPERVISOR THERMAL SOT23-6
MIC2800-GFSYML TR IC REG TRPL BUCK/LINEAR 16MLF
MIC281-7BM6 TR IC SUPERVISOR THERMAL SOT23-6
MIC2810-1JGMYML TR IC REG TRPL BUCK/LINEAR 16MLF
MIC284-2BMM TR IC SUPERVISOR THERM 2ZONE 8-MSOP
MIC3385-1.5YHL TR IC REG DL BCK/LINEAR SYNC 14-MLF
相关代理商/技术参数
MIC2593-2YTQ 功能描述:热插拔功率分布 Dual-slot PCI Hot Swap Power Controller w/o IPMI support - Lead Free RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MIC2593-2YTQ TR 功能描述:热插拔功率分布 Dual-slot PCI Hot Swap Power Controller w/o IPMI support - Lead Free RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MIC2594-1BM 功能描述:IC CTRLR HOT SWAP NEG HV 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP(3x3) 包装:管件
MIC2594-1BM TR 功能描述:IC CTRLR HOT SWAP NEG HV 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP(3x3) 包装:管件
MIC2594-1YM 功能描述:热插拔功率分布 Negative Voltage Hot-Swap Controller - Lead Free RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MIC2594-1YM TR 功能描述:热插拔功率分布 Negative Voltage Hot-Swap Controller - Lead Free RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube
MIC2594-1YM-TR 功能描述:Hot Swap Controller 1 Channel -48V 8-SOIC 制造商:microchip technology 系列:- 包装:剪切带(CT) 零件状态:停产 类型:热交换控制器 通道数:1 内部开关:无 应用:-48V 特性:故障超时,闭锁故障 可编程特性:限流,压摆率,UVLO 电压 - 电源:-80 V ~ -19 V 电流 - 输出(最大值):- 工作温度:-40°C ~ 85°C 电流 - 电源:3mA 安装类型:表面贴装 封装/外壳:8-SOIC(0.154",3.90mm 宽) 供应商器件封装:8-SOIC 功能引脚:DRAIN,OFF,ON,PWRGD 标准包装:1
MIC2594-2BM 功能描述:IC CTRLR HOT SWAP NEG HV 8-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP(3x3) 包装:管件